Serving Raleigh, Durham, Fayetteville, Greensboro, Greenville, Wilmington, Cary, NC and surrounding cities

Serco Level Lift Model

Benefits

High-performance dock leveler — it provides the same performance benefits of a hydraulic dock leveler such as regenerative hydraulics, powered lip control, safety velocity fuse and push-button controls.

Below-dock operation — In scissor mode, it eliminates the steep grade differences between the vehicle bed and the leveler deck, providing safe, level, below-dock operations.

Scissors lift versatility — Unlike standard scissor lifts, the hydraulically powered dock lip ensures faster cycling times and its lifting capacity can handle the toughest loads while also providing dock-to-grade-level forklift access

Design Highlights
  • 50,000 lbs. Capacity Leveler (per ANSI MH14.1-1987)
  • 12,000 lbs. Capacity Lift (8 ft. long units)
  • 20,000 lbs. Capacity Lift (10 & 12 ft. long units)
  • 18″ Lip Standard
  • LED Light Communication Package
  • Remote 7.5 HP Independent Lift Motor & Hydraulic System
  • PLC Operation
  • 1 HP Independent Leveler Motor & Hydraulic System
  • Full Feature NEMA 12 Control Panel with Mushroom Style Stop Button
  • Remote NEMA 4X Pendant Push Button Hand Control
  • Interior Warning Light & Audible Alarm Indicate Dock Lift Is Not In Stored Position
  • Safety Velocity Fuse on Leveler and Lift
  • Guard Rail Package
  • Rear Hinge Blocks
  • Protective Roller Curtain on Front
  • Side and Rear Weatherseal
  • Grease Fittings

Serco Rail Lift Model

Design Highlights
  • Low Profile for Surface-mounted Applications z No Pit Construction Required
  • Three-sided Platform
  • Heavy-duty I-beam Deck Understructure
  • Excellent End-load Stability in Fully Raised Position z Displacement style Cylinder with Internal Stops
  • Self-contained Power Unit/control Panel
  • Standard Pre-wired Control Panel
  • NEMA 4X Push-button Controller with 15’ Cord
  • Superior Speed-to-horsepower Ratio Compared to Scissor-style Dock Lifts
  • Direct thrust Cylinders Provide Constant Speed Through Full Range of Travel
  • Checker Plate or Smooth Deck Surface z Sealed Guide Bearing Rollers
  • Fused 24-volt Control Circuit

Serco Loadwarrior Air Lift Model

Design Highlights
  • No lag down, portable design
  • Pallet jack pockets built in
  • Removable gibs
  • Over-pressure relief valve
  • Operating angle from horizontal to 30 degrees from horizontal
  • Heavy-duty airbag
  • Downspeed flow control
  • Works on “shop air,” 80psi
  • Includes a hand or foot valve control and a 6′ hose
  • Meets or exceeds the ANSI MH29.2 standard for industrial scissor lift

Serco Loadwarrior Turntable Model

Manual or powered models are available to efficiently palletize, build-up and break-down, and either can be mounted on a scissors lift, stable bench, or other surface. In addition, ground-mounting is also available.

Design Highlights
  • Rigid base frame with predrilled mounting holes
  • 1/2″ thick steel platform with rounded corners
  • Tough TGP hard-chromed kingpin
  • Rollers are sealed ball bearings for ease of operation
  • Roller-pin bushings are self-lubricating
  • 34″ x 34″ is minimum turntable size

Serco Scissors Dock Lift Model SDL68-5

Our Dock Lifts can accommodate a wide variety of truck styles; from 20″ step vans or pick-up trucks to high cube vans, standard semi-vehicles and 60″ high stake bed vehicles. They can be pit or surface-mounted inside the building or in front of the loading dock. (Surface-mounted dock lifts can be relocated if used in applications where a pit or permanent installation is prohibited.)

Design Highlights
  • Beveled toe guards
  • 18″ standard solid or split bridge plate
  • Dual hydraulic lifting cylinders for optimum performance
  • Velocity fuses on lift cylinders prevent uncontrolled descent
  • Removable, mandrel-formed tubing handrails
  • Maintenance safety strut
  • Safety tread steel deck
  • Safety chains across operating ends
  • Upper travel limit switch
  • Available in 4,000-20,000 lb. capacities

Serco Loadwarrior Double Scissors Table Model

Design Highlights
  • Pre-wired power unit with UL approved control components
  • Internally mounted 5 hp power unit
  • Self-lubricating composite bearings
  • Solid steel legs with stiffener bars
  • Turned, ground, polished and hard-chromed axle pins
  • Double-wire braided hydraulic hoses
  • Velocity fuses on all cylinders to prevent uncontrolled descent
  • Polyethylene reservoir allows easy visual check of oil level
  • Maintenance locks built into base frame
  • Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts
SPEC SHEETBROCHURE

Serco Loadwarrior Tilter Model

Design Highlights
  • Pre-wired power unit with UL approved control components
  • Power unit internally mounted
  • Available in 1 1/2 hp three-phase or 3/4 hp single-phase with 24V AC control valve
  • Self-lubricating composite bearings
  • Velocity fuses on all cylinders to prevent uncontrolled descent
  • Double wire braided hydraulic hoses
  • Polyethylene reservoir allows easy visual check of oil level
  • Maintenance locks built into frame
  • Standard 12′ high lip
  • 28″ W x 38″ L minimum platform size
  • Meets or exceeds the ANSI MH29.2 standard for industrial tilters

Serco Loadwarrior Scissor Table Model

Design Highlights
  • Solid steel legs with stiffener bars for extra strength and support
  • Polyethylene tank prevents condensation, provides easy check of oil level
  • High-pressure cylinders with safety velocity fuses to prevent uncontrolled descent
  • Pre-wired NEMA-rated controls
  • High-strength roller pins with snap rings
  • Hardened steel rollers
  • High-strength steel polished axle pins
  • UL-approved control components
  • Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts
SPEC SHEETBROCHURE

Serco Loadwarrior Air Tilter

Design Higlights
  • Reinforced, heavy-duty airbag
  • Air damper reduces platform bounce
  • Fork pockets for simple mobility